- wusheng888@126.com
- Monday-Friday:09:30 pm-05:00pm
- Address: Unit 1111, 11/F, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, HongKong.
Optocouplers (Photocell (CdS) Output)
The CdS photocell output optocouplers optically couple an LED to a CdS Light Dependent Resistor (LDR). The LDR resistance increases when the LED current is OFF and decreases when LED current is ON. The device showcases a large dynamic range with a response time that efficiently mimics the human eye's sensitivity to light changes. Engineered with High, Medium, and Low dark resistances, the optocouplers are available with diverse resistance values to suit various applications. The photocells are encased in an opticallyisolated structures.
Type No.: NSL-37V33
*100Ω ON-Resistance Photocell (CdS) Output Optocoupler
■Typical Applications:
● Industrial
● Audio Compressors
● Electrical Noise Filter
■Features
● Compact Moisture Resistant Package
● Low LED Current
● Very Low “On” Resistance
●Passive Resistance Output
●Low Distortion
■Absolute Maximum Rating:
| Parameter | Symbol | Min | Max | Unit |
| Isolation Voltage | V_ISO | - | 2500 | V |
| Operating Temperature | T_OP | -40 | +75 | °C |
| Storage Temperature | T_STG | -40 | +75 | °C |
| Package | Plastic | |||
*0.118 inch from base for 3seconds with heat sink
■Typical Electro-optical characteristics rating (Ta=25 ℃ unless otherwise noted)
| Parameter | Test Conditions | Symbol | Min | Typ | Max | Unit |
| LED | ||||||
| Forward Current | - | I_F | - | - | 40 | mA |
| Forward Voltage | I_f=20mA | V_F | - | - | 2.5 | V |
| Reverse Current | - | V_R | - | - | 3.0 | V |
| PHOTOCELL | ||||||
| Maximum Photocell Voltage | Peak AC or DC | V_C | - | - | 100 | V |
| Power Dissipation¹ | - | P_D | - | - | 175 | mW |
| COUPLED | ||||||
| On-Resistance | I_f=1.0mA | R_on | - | 20 | - | KΩ |
| I_f=10mA | R_on | - | 600 | - | Ω | |
| I_f=40mA | R_on | - | 200 | 500 | Ω | |
| Off Resistance | 10 sec after I_f=0mA | R_off | 50 | - | - | MΩ |
| Rise Time | Time to reach 63% of final Ron @ I_f=40mA | T_R | - | 2.5 | - | msec |
| Decay Time | Time to 100KΩ from removal of I_f=40mA | T_F | - | - | 35 | msec |
| ¹Derate linearly to 0 at 75°C | ||||||
■Mechanical Specifications
Units are in inches [mm]
■General Care and Handling Instructions
Handling and Storage
• Handle Optocouplers and LEDs gently to prevent damage.
• Avoid exposing the devices to temperatures exceeding the storage temperature rating of the device.
• Maintain a non-condensing environment for optimum performance and lifetime.
Cleaning
• For plastic molded devices, cleaning with a 50/50 mixture of Methanol and isopropyl alcohol is recommended. Cleaning in an ultrasonic bath is generally not recommended.
Special Considerations
• Avoid exposing plastic molded devices or epoxy glob topdevices to harsh chemicals like THINNERS, ACETONE, andTRICHLOROETHYLENE.
■Legal Disclaimer
Information in this data sheet is believed to be correct and reliable. However, no responsibility is assumed for possible inaccuracies or omission. Specifications are subject to change without notice.
Ne peut être vide
Le format de courrier électronique n’est pas correct
Ne peut être vide
